VR3000 EX Manual

・Headphones (main unit)
・Ultra-low-latency USB transceiver (USB-A)
・Quick Manual
・“Safety Instructions / Warranty Terms” booklet

A：Power Button
B：Volume Control Dial
C：MODE Button
D：Control (C) Button
E：LED Indicator
F：USB Port
G：Boom Microphone

Please charge the headphones according to the recommended USB charging environment below. While charging, the headphone’s charging indicator will blink orange. When charging is complete, the indicator will light up white.

※A charging cable is not included. Please use a commercially available USB cable.

【Recommended USB Charging Environment 】
USB Charger: A commercially available USB charger capable of supplying an output current of 1A or more
USB Cable: USB Type-C cable (USB standard compliant)

When you press and hold the Power button for approximately 3 seconds, a confirmation tone will sound and the device will turn ON.
For about 3 seconds immediately after powering ON, the LED indicator will light up according to the remaining battery level, as shown in the diagram below.

Battery Level	LED Indicator
0〜29%	LED lights up in orange ※
30%〜100%	LED lights up in white

※ After lighting up, the LED will continue blinking in orange for a certain period.

When you press and hold the power button for approximately 3 seconds, a confirmation tone will sound and the device will turn OFF.
Immediately after turning off the power, the LED indicator will light for about 3 seconds according to the remaining battery level, as shown in the diagram below.

Battery Level	LED Indicator
0〜29%	LED lights up in orange
30%〜100%	LED lights up in white

When the ultra-low-latency USB transceiver is connected to a gaming device or PC that supports USB connections, it powers ON automatically and enters pairing mode. At this time, the indicator on the transceiver lights up in orange for about 10 seconds. With the transceiver in this state, turn ON the headphones and switch to USB mode. After the pairing guidance, you will hear the connection confirmation (“USB connected”), indicating that the automatic connection to the transceiver is complete. At this time, the indicator on the transceiver lights up in white for about 10 seconds.
※ Press and hold the MODE button for 3 seconds to switch between USB mode and Bluetooth mode. When using low-latency wireless communication, switch to USB mode.
※When USB mode is selected, the Bluetooth connection is disconnected.
※Depending on the gaming device or PC, you may need to change the sound output to this product in the system settings.
※Volume control and other operations may vary depending on the device connected to the transceiver.
※When connecting via a USB hub, the device may not operate correctly.

【About the Audio Mixer Function】
When using a Windows PC, this feature allows you to set the game volume and the volume of third-party voice-chat software independently.

【Setup Procedure】
1. Plug the transceiver into the USB-C port of your PC.
2. When connected, the following two audio devices will appear.
・VR3000 EX - Game
・VR3000 EX - Chat
3． In the in-game audio output settings, select “VR3000 EX – Game.”
4. When using third-party voice-chat software, select “VR3000 EX – Game” for both audio output and microphone input. If using the in-game chat function, select “VR3000 EX – Game” as the microphone input.
5. Adjust the game and chat volumes separately using the Windows “Volume Mixer.”

If the transceiver is removed from the device during ultra-low-latency wireless communication, or if the headphones are switched to Bluetooth mode, the ultra-low-latency wireless connection will be disconnected.
To reconnect the headphones, reconnect the transceiver to the device or switch the headphones back to USB mode. Once the automatic connection between the transceiver and the headphones is established, the transceiver’s indicator will light up in white for 10 seconds.
※Press and hold the MODE button for 3 seconds to toggle between USB mode and Bluetooth mode.

When connecting your headphones to a smartphone or other device for the first time, pairing is required. Once pairing has been completed, the paired devices will automatically connect the next time you turn on the headphones.

【Performing Initial Device Pairing】
1.Press and hold the Power button for approximately 3 seconds. After the “Power On” guidance, you will hear “USB Pairing.” ※1
2.Press and hold the MODE button for about 3 seconds to switch to Bluetooth mode.
3.On your smartphone or other device, turn on the Bluetooth function.From the pairing screen, select “final_VR3000 EX.” Once your device displays “final_VR3000 EX – Connected”※2, pairing is complete.

【Re-Pairing or Pairing with an Additional Device】
1. On any device that has already been paired, either turn off the Bluetooth function or delete the pairing information.
2.Press and hold the Power button for approximately 3 seconds.「After the “Power On” guidance, you will hear either “USB Pairing” or “Bluetooth Pairing.”If you hear “USB Pairing,” press and hold the MODE button for 3 seconds to switch to Bluetooth mode.Press and hold the Power button for approximately 3 seconds.「After the “Power On” guidance, you will hear either “USB Pairing” or “Bluetooth Pairing.”If you hear “USB Pairing,” press and hold the MODE button for 3 seconds to switch to Bluetooth mode.
3.On your smartphone or other device, turn on the Bluetooth function. From the pairing screen, select “final_VR3000 EX.” Once your device displays “final_VR3000 EX – Connected,” pairing is complete.On your smartphone or other device, turn on the Bluetooth function. From the pairing screen, select “final_VR3000 EX.” Once your device displays “final_VR3000 EX – Connected,” pairing is complete.

※1 At the time of factory shipment, the headphones are set to USB mode.
※2 The wording displayed may vary depending on your smartphone or connected device.

【How to Reset the Headphones】
If Bluetooth pairing does not work properly, or if an unexpected error occurs during low-latency wireless communication causing malfunction, you can reset the headphones by following the steps below. After the reset is complete, please try pairing again.
1.With the headphones powered on, press and hold the Control (C) button for approximately 10 seconds.With the headphones powered on, press and hold the Control (C) button for approximately 10 seconds.
2.Release your finger when the “Power ON” guidance is followed by the “USB Pairing” guidance ※.
※At this point, the reset is complete and the headphones return to factory settings. All stored Bluetooth pairing information will be deleted. Please delete the pairing information for these headphones from your smartphone or other device as well, then perform Bluetooth pairing again.At this point, the reset is complete and the headphones return to factory settings. All stored Bluetooth pairing information will be deleted. Please delete the pairing information for these headphones from your smartphone or other device as well, then perform Bluetooth pairing again.

【For low-latency wireless communicationFor low-latency wireless communication】
If the ultra-low-latency USB transceiver is connected to a gaming device, after completing step 2, remove the transceiver once and reconnect it to the gaming device.

This mode slightly enhances in-game footsteps, making it easier to detect enemy positions. It is recommended for FPS games or situations where you want to focus on enemy footsteps. You can toggle this mode ON/OFF by pressing the Control (C) button once.
※When the Control (C) button is pressed and two beeps are heard, Footstep Mode is enabled. When one beep is heard, Footstep Mode is disabled.
※You can also configure this setting in the dedicated “final VR3000 EX” app.

The boom microphone included with this product allows you to make calls when the microphone arm is lowered. When you lower the boom arm to its fixed position, the microphone mute will be disabled and you can speak.
※To unmute the microphone, make sure to lower the boom arm firmly until it clicks into place. When you do not need to use the microphone, raise the boom arm firmly to its fixed upper position to mute it.
※When using the ultra-low-latency USB transceiver, select “VR3000 EX - Game” to use the boom microphone.

Music	Play	Press the MODE Button once
	Pause	Press the MODE Button once
Incoming Call	Answer Call	Press the MODE Button once
	End Call	Press the MODE Button once
	Reject Call	Press the MODE Button twice
Music / Calls (Common Controls)	Increase Volume	Turn the volume control dial upward ※１
	Decrease Volume	Turn the volume control dial downward ※1

※1 When using USB mode, the playback device must be set to “VR3000 EX - Game.” If “VR3000 EX - Chat” is selected, the operation direction of the volume control dial will be reversed. To increase the volume, turn the dial downward; to decrease the volume, turn the dial upward.
※ Depending on the connected device, some functions may not operate correctly.

“final VR3000 EX” is a dedicated app that allows you to customize the headphones to your personal preferences. By downloading the app onto the device paired with your headphones, you can use the following features. We highly recommend downloading the app to enhance your experience.

・Footstep Mode: Slightly enhances the frequency range of in-game footsteps, helping you detect enemy positions more easily in FPS games.
・10-Band Equalizer: Adjust individual frequency levels to fine-tune the sound quality to your liking.
・Firmware Updates
・App Language Switching
・Auto Power-Off Function: Automatically turns off the headphones after a period of silence or inactivity.
・News Notifications & Battery Level Check

・Cause1：(Immediately after purchase) Battery level is low
For safety during international transport, the built-in battery cannot be fully charged at shipment due to IATA regulations. As a result, the battery level may be below the required operating voltage when the package is opened. Please fully charge the headphones before use. For charging instructions, refer to the section above titled “Charging ”.

・Cause2：Power button has not been pressed long enough
Press and hold the power button until the headphones turn ON. For details, refer to “Turning ON the Power”.

Cause：Output of the USB adapter being used is low
When using a USB port on a PC or similar device, the output may be insufficient, causing charging to take longer than expected. Please use a USB adapter capable of 5V / 1A or higher.

Cause：Power button has not been pressed long enough
Press and hold the power button until the headphones turn OFF. For details, refer to “Turning OFF the Power”.

・Cause1：Headphones are not in pairing mode
In some cases, performing a reset operartion may fix the problem. Please refer to the section above titled "Performing Factory Reset". 。

・Cause2：Automatically reconnecting to a previously paired device
Please delete the pairing information of the previously paired device, and then perform the pairing operation again.

・Cause3：The device is in USB mode
Please press and hold the MODE button to switch to Bluetooth mode.Please press and hold the MODE button to switch to Bluetooth mode.

Cause：External interference affecting connection stability
Bluetooth and the ultra-low-latency USB transceiver communicate using the 2.4GHz band which might be interefered by other wireless standards such as Wi-Fi, etc. Moreover, the connection is sensitive against liquid where humidity, rain, or even the size of head could cause disruption to the connection. The specifications of the device to be connected could cause variation too. For that reason, reducing the distance between devices or switching OFF unused Wi-Fi/Bluetooth of surrounding devices may improve the connection.

・Cause1：The boom microphone is not lowered to its lowest position
Lower the boom microphone to its lowest position and unmute it.

・Cause2：The microphone input in the application is muted, or another input device is selected
Unmute the microphone input in the application, or ensure no other input device is selected.

・Cause3：An input device other than ‘VR3000 EX - Game’ is selected
When using the ultra-low latency USB transceiver, select ‘VR3000 EX - Game’ as the input device.

If dirt such as skin oils accumulates on the headband or earpads, gently wipe it off with a soft, dry cloth.

The rechargeable batteries built into the equipment are recyclable. During disposal, please follow the instructions from your local municipal government and do not attempt to disassemble the product.

The warranty for this product is valid for 1 year from the date of purchase. During the warranty period, we will repair the product based on the provisions below. The warranty is only valid in the country in which the product was purchased. Regarding questions pertaining to repairs, please contact the store you purchased the product from or contact us by visiting our “Contact” page.
1. If the product malfunctions within the warranty period under the usage conditions specified in the warnings and cautions of this manual, we will repair it free of charge.
2. In the following cases, repairs to the product will be subject to a fee even during the warranty period:
(1) Original purchase receipt or other documentation showing the date of purchase are failed to be presented.
(2) The product is identified to be modified, disassembled, or repaired by a third party or customer other than our company or our authorized organizations.
(3) The earphones were subjected to a strong impact or were allowed to get wet. Product failure resulting from an excessive use of force on the product.
(4) Failure due to fire, earthquake, wind, flood, lightning, or other acts of God, human error, theft, or virus and malware infection.
(5) Repair of scratches on the surface of the housing or repair of the housing itself.
3. We shall not be liable for any incidental or consequential damages for breach of any express or implied warranty or condition on this product. Nor shall recovery of any kind against us be greater than the original purchase price of the product from us or an our authorized dealer

Please contact us by visiting our official “CONTACT” page